Just as in the other instructable, use the observation command to send some fake data to verify everything works. Follow the instructions in the comments and the device should be registered. I only wanted to add a Temperature sensor so I commented out the humidity sensor. Once you have the IoTKit library installed in your IDE, open up the IoTkitRegisterExample. Make sure you follow it though creating an account and registering the device. This also should serve as an introduction to working with IoTKit.Īlthough their instructable does a great job detailing the process, I found an easier way to set up new devices and register them with the Panel. I was following 10DotMatrix's guide for setting up the Analytics Panel. While Intel does a good job with those steps (to some degree) this is where things get hairy. If everything went well, you should be able to login with the IP Address they give you on any browser in the network. **Another note, I couldn't for the life of me figure out how to connect to my network as I was still on WEP (I know), so I had to change the security settings in my router to WPA2 Personal to get a key which the Edison accepted. Work through their process and use their nice guide to connect to your WiFi network. Once you login, type configure_edison -setup *It is important to note that the Serial connection times out, so if you hit a character and nothing shows up, just hit it again as the first key "wakes" it. To connect up with WiFi and to clean up some configuration stuff, open up an SSH again (if you closed it from last time) If everything so far has went as planned, the on-board LED should start blinking. Open up Device Manager again and find the COM port that is the Edison Virtural COM Port and set that in the IDE After the gruesome download from Intel or a less so awful download from my mirror, open up the Arduino exe. The next step is to get their modified version of the Arduino IDE working. Screens will whir by and it will finish the process sooner or later Once you get past the login screen, type reboot ota and hit Enter You might need to hit enter two times to get a login screen, but once you do, type root and hit Enter Now open up PuTTY or your SSH client of choice, set it to connect to Serial over the COM port you found and set the baud rate to 115200 Make sure to remember which one is the USB Serial Port Intel's site has a picture of their device manager to show how to pick which COM port to use in your SSH client of choice, but there are multiple Edison ports, which is pretty confusing. Then, you copy over all the files from the "Latest Image" to the root of the microSD card which should show up under the name EDISON Intel wants to make sure the microSD card is empty before we copy over the new OS files, so they describe a verbose command prompt way of erasing the files, but you could just as easily delete them from Explorer. Make sure the micro switch is flipped towards the microUSB ports and plug two USB cables into those ports and into your computer. Windows users have to install the drivers, both the FTDI and Edison-specific ones. The download speed from Intel was horrid as it took over five hours for me to get the IDE files, so I will provide mirrors at the end of this Instructable. Once you download all of their files, we can get started flashing the device. You can find Linux and Mac instructions there tooįirst they have you mount the Edison and attach the posts (I don't think this step will be a problem). You can follow my guide or theirs, it's pretty much the same, but I provided mine in case you wanted a different perspective.įor windows at least, they provide these links: You will even be able to program the Edison over USB and wireless both in Arduino C++ and Python.As I'm sure my fellow makers have discovered, Intel's site is a little lackluster in describing in detail the workings of setting up this device. Once you have completed this book your Edison will be up and running with the latest software version, and you will have sufficient knowledge of both hardware and software to start making your own applications. We will use Wi-Fi and Bluetooth to set up wireless connections, and show you a trick to program sketches over Wi-Fi. We will discuss Linux, Arduino C++ and Python, and show examples of how the Edison can interface with other hardware. We will use the Edison Arduino break-out board because it is easy to work with. In this eBook we will help you get up-to-speed with the Edison, by installing the software both on the Edison as well as on your Windows PC. A tiny computer, the size of a postage stamp, with a lot of power and built-in wireless communication capabilities. The Internet of Things is rapidly gaining interest, and that has fueled the development of the Edison.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |